Grinding Mill

Focus on the field of micro powder grinding equipment

Introduction of Talc Ball Mill

talc ball mill

Clirik talc ball mill is widely used for micron powder producing. It is suitable to grind the material with middle and low hardness, moisture below 6%, and the material should be non-explosive and non-flammable, such as: calcite, chalk, limestone, dolomite, kaolin, mica, magnetite, vermiculite, meerschaum, gypsum, graphite, fluorite, phosphate ore,potassium ore pumice, etc.

Application of Talc Ball Mill

talc ball mill is the new type mining equipment for making micro powders, fine powders,which is widely applied in the industries of metallurgy, mining, chemistry, cement, construction, refractory materials, ceramics, and so on.The purpose of the micro powder grinding mill for super-fine grinding materials with hardness less than 9 in Moh’s scale and humidity less than 6 percent such as kaolin, limestone, calcite, marble, talcum, gypsum, dolomite, mica, carbon black, graphite, fluorite, potassium feldspar, pigment, up to 200 kinds.

Working Principle of Talc Ball Mill

When the ball mill is at work, all the grinding rollers are rolling in the ring, and the materials are driven to the edge of the turnplate by the centrifugal force and fall down into the grinding chambers where the materials are repeatedly pressed, crushed and grinded by the rollers.

The high-pressure air blower constantly inhales air within the grinding mill and, in turn, the airflow with crushed materials are brought to the classifier whose high-speed impeller will screen the airflow: the unqualified particle size will fall and return to the mill for being reground while the qualified particle size mixed with air will go into the cyclone powder collector. Most of the qualified powders will fall and exit from the discharging valve at the bottom; a small proportion of the fine powders, with airflow, moves to the dust cleaner, and clings to the surface of the filter bags. At the same time, the fine powders clinging to the surface fall down by the sudden vibration of the filter bags, which is caused by the instantly ejected high-pressure gas controlled by the pulse valve. The materials from the above two lots are sent by the conveyor at the bottom to get finished powders packed. In addition, filtered clean air will be emitted from the air outlet of muffler in the end.

Advantages of Talc Ball Mill

1.High Efficiency

Under the same finished final size and the same motor power, the capacity of the machine is twice as much as jet mill, mixing grinder and ball mill, and energy consumption decreased 30%.

2.Long lifecycle of spare parts

The ring and roller are forged by special material with high utilization,the lifetime can reach 2-5 years for grinding calcite carbonate.

3.High safety and reliability

As no rolling bearings or screws in grinding cavity, there are no problems caused by bolts shedding or rapid wear of bearings and seal components.

4.High fineness, flexible adjustment

The final fineness of the grinding materials can be adjusted between 325 meshes and 2500 mesh (47-5 micron), and the product fineness can reach D97≤5μm.

5.Environment-friendly

Technical Parameters of Talc Ball Mill

Model Cylinder rotary speed(r/min) Loading ball weight(t) Input size(mm) Discharge size(mm) Capacity(t/h) Motor power (kw) Weight (t)
Ф900×1800 39 1.5 ≤20 0.075-0.89 0.8-2 18.5 4.6
Ф900×3000 39 2.7 ≤20 0.075-0.89 1-4 22 5.6
Ф1200×3000 36 3.5 ≤25 0.074-0.4 1.6-5 37 12.8
Ф1200×4500 32 5 ≤25 0.074-0.4 1.6-5.8 55 13.8
Ф1500×3000 27 7.5 ≤25 0.074-0.4 2-5 75 15.6
Ф1500×5700 28 12 ≤25 0.074-0.4 3.5-6 130 24.7
Ф1830×3000 25 11 ≤25 0.074-0.4 4-10 130 28
Ф1830×6400 24 21 ≤25 0.074-0.4 7-16 210 34
Ф1830×7000 24 23 ≤25 0.074-0.4 8-18 245 36
Ф2100×3600 23 19 ≤25 0.074-0.4 10-36 210 46
Ф2200×4500 21 27 ≤25 0.074-0.4 12-23 280 48.5
Ф2200×6500 21 35 ≤25 0.074-0.4 14-26 380 52.8
Ф2200×7000 21 35 ≤25 0.074-0.4 15-28 380 54
Ф2200×7500 21 35 ≤25 0.074-0.4 15-30 380 56
Ф2400×4500 21 30 ≤25 0.074-0.4 18-45 320 65
Ф2400×8000 20 36 ≤25 0.074-0.4 20-48 410 81
Ф2700×3600 21 39 ≤25 0.074-0.4 19-75 400 83
Ф2700×4000 20 40 ≤25 0.074-0.4 20-78 400 85
Ф2700×4500 20 48 ≤25 0.074-0.4 22-85 430 89
Ф3200×4500 18 65 ≤25 0.074-0.4 29-140 800 137
Ф3200×5400 18 81.6 ≤25 0.074-0.4 30-180 800-1000 146
Ф3600×4500 17 88 ≤25 0.074-0.4 35-210 1000 190
Ф3600×6000 17 117 ≤25 0.074-0.4 38-240 1250-1500 220
Ф3600×8500 17 144 ≤25 0.074-0.4 45-260 1800 260

 

 


菜单
//底部调用